Help UBCT9
Forum rules
***NOTE*** This forum and its content are not endorsed in any way by the vendor and users are advised to exercise caution when viewing and/or acting on any information contained within. We accept no responsibility for your devices and strongly warn you to check your warranty conditions and seek expert advice before proceeding.
***NOTE*** This forum and its content are not endorsed in any way by the vendor and users are advised to exercise caution when viewing and/or acting on any information contained within. We accept no responsibility for your devices and strongly warn you to check your warranty conditions and seek expert advice before proceeding.
-
- Registered User
- Posts: 5
- Joined: Sun Jul 22, 2012 10:23 am
Help UBCT9
Hi I am having issues with my Uniden Scanner UBCT9. It picks up the 88-108 Mhz but won't pick up anything higher. Even if I set the frequency and TX from a handheld around 20 meters away. It was working great a few months ago but now it's just a little weird. When in the 400-512 range I try and set the squelch to off and still get no hiss or any transmissions. however I am wondering if when I was setting up the unit again I pressed something and am not sure what. I know the models up from this have a reset ability but after looking in the manual for it, had a read page to page and can't find anything. does anyone have any idea what I can do or what could be wrong? as far as I am aware and from what I have read about this similar issue is if I can get transmissions from 88-108 everything is fine. I am just lost. I know I should be able to pick up something. I know I can where I am cause my programmable handheld picks up the Ambo's and fireies up here. please any advice would be greatly appreciated.
- bodyguard
- Registered User
- Posts: 1210
- Joined: Fri Aug 31, 2007 7:54 pm
- Location: Brisbane, QLD
Re: Help UBCT9
Had the same problem with my T9,
ended up dumping it cause Uniden couldn't / wouldn't supply a main board for it
ended up dumping it cause Uniden couldn't / wouldn't supply a main board for it
Cheers
BG
UBC9000XLT, UBCT8, BCT15X, UBC92XLT, Kenwood R-5000, PSR-410 , KG-UVD1P
BG
UBC9000XLT, UBCT8, BCT15X, UBC92XLT, Kenwood R-5000, PSR-410 , KG-UVD1P
-
- Registered User
- Posts: 5
- Joined: Sun Jul 22, 2012 10:23 am
Re: Help UBCT9
damn it. and don't have the money to replace it. It's didn't cost me anything to begin with but that is ok. were you able to inspect the main board at all? see any visual signs like blown caps etc?
- bodyguard
- Registered User
- Posts: 1210
- Joined: Fri Aug 31, 2007 7:54 pm
- Location: Brisbane, QLD
Re: Help UBCT9
I had a radio tech look at it, they are surface mount components, but he was very sure thats where the problem lay.
Then Uniden couldn't/wouldn't supply the board and the radio became history.
I have seen on many forums, the same problem happening to the T9, yet the T8 I have works flawlessly
Sorry I couldn't be any more help
Then Uniden couldn't/wouldn't supply the board and the radio became history.
I have seen on many forums, the same problem happening to the T9, yet the T8 I have works flawlessly
Sorry I couldn't be any more help
Cheers
BG
UBC9000XLT, UBCT8, BCT15X, UBC92XLT, Kenwood R-5000, PSR-410 , KG-UVD1P
BG
UBC9000XLT, UBCT8, BCT15X, UBC92XLT, Kenwood R-5000, PSR-410 , KG-UVD1P
-
- Registered User
- Posts: 5
- Joined: Sun Jul 22, 2012 10:23 am
Re: Help UBCT9
oh well.... might just see if I can off load it to someone who might want it. unless someone on here would like it for parts. really cheap $50 lol
-
- Registered User
- Posts: 231
- Joined: Wed Feb 10, 2010 9:43 pm
- Location: Lockyer Valley, Qld
Re: Help UBCT9
I had a T9 and it wasn't very old and crapped itself. Uniden refunded my money rather than fix it. My T8 works great though.
Steve
-
- Registered User
- Posts: 5
- Joined: Sun Jul 22, 2012 10:23 am
Re: Help UBCT9
sounds like the T9 was a really big dodgy model
- Stretch
- Forum Manager
- Posts: 3528
- Joined: Thu Aug 09, 2007 8:29 pm
- Location: Gold Coast
- Contact:
Help UBCT9
Never had a problem with my T8
Cheers,
Mitch
Sent from my iPhone using Tapatalk
Cheers,
Mitch
Sent from my iPhone using Tapatalk
Mitch Rogers
-
- Registered User
- Posts: 5
- Joined: Sun Jul 22, 2012 10:23 am
Re: Help UBCT9
man why couldn't I have inherited a T8
- bodyguard
- Registered User
- Posts: 1210
- Joined: Fri Aug 31, 2007 7:54 pm
- Location: Brisbane, QLD
Re: Help UBCT9
never have I, the T8 is great the T9 for some reason is causing this griefStretch wrote:Never had a problem with my T8
Cheers,
Mitch
Sent from my iPhone using Tapatalk
Cheers
BG
UBC9000XLT, UBCT8, BCT15X, UBC92XLT, Kenwood R-5000, PSR-410 , KG-UVD1P
BG
UBC9000XLT, UBCT8, BCT15X, UBC92XLT, Kenwood R-5000, PSR-410 , KG-UVD1P
-
- Registered User
- Posts: 18
- Joined: Wed Jan 31, 2018 7:35 pm
Re: Help UBCT9
Seems like im having the same problem. Can hear the local 101.7 radio station but cant hear myself on uhf17.... So its time to throw it out?